ctbtodev
Last change
on this file since 3f383fe was
3f383fe,
checked in by Anne Philipp <anne.philipp@…>, 4 years ago
|
added a known issue to the online docu
|
-
Property mode set to
100644
|
File size:
2.3 KB
|
Line | |
---|
1 | Known Bugs and Issues |
---|
2 | ********************* |
---|
3 | |
---|
4 | Release v7.1 |
---|
5 | ============ |
---|
6 | |
---|
7 | |
---|
8 | CDS API and ERA5 data |
---|
9 | --------------------- |
---|
10 | |
---|
11 | See ticket `#230 <https://www.flexpart.eu/ticket/230>`_ on flexpart.eu for information. |
---|
12 | |
---|
13 | |
---|
14 | Installation problems with ``GATEWAY`` and ``DESTINATION`` parameters |
---|
15 | --------------------------------------------------------------------- |
---|
16 | |
---|
17 | See ticket `#263 <https://www.flexpart.eu/ticket/263>`_ on flexpart.eu for information. |
---|
18 | |
---|
19 | |
---|
20 | Installation problems with the Fortran program ``calc_etadot`` |
---|
21 | -------------------------------------------------------------- |
---|
22 | |
---|
23 | See ticket `#264 <https://www.flexpart.eu/ticket/264>`_ on flexpart.eu for information. |
---|
24 | |
---|
25 | ECCODES Error Code 250 |
---|
26 | ---------------------- |
---|
27 | |
---|
28 | If you get an error message from ECCODES with code 250, locking like this: |
---|
29 | |
---|
30 | .. code-block:: bash |
---|
31 | |
---|
32 | ECCODES ERROR : wrong size (184) for pv it contains 276 values |
---|
33 | ECCODES ERROR : get: pv Passed array is too small |
---|
34 | ... ERROR CODE: 250 |
---|
35 | ... ERROR MESSAGE: |
---|
36 | Command '['<path-to-flex_extract>/flex_extract_v7.1/Source/Fortran/calc_etadot']' returned non-zero exit status 250. |
---|
37 | ... FORTRAN PROGRAM FAILED! |
---|
38 | |
---|
39 | then you have set a wrong maximum level in the :literal:`CONTROL` file! |
---|
40 | It is important to properly select the maximum level depending on the data set you would like to retrieve. The following model level definitions (number of model levels available) are limited to [16, 19, 31, 40, 50, 60, 62, 91, 137]. The ERA-Interim data set uses 62 model levels and *ERA5* as well as *CERA-20C* uses 137. The operational data set uses different model levels depending on the date. For example, on the 25/06/2013 the operational system started to use 137 model levels. Therefore, everytime you extract data from a date later than 25/06/2013 you have to select LEVEL=137 in the :literal:`CONTROL` file or define a LEVELLIST=1/to/137. Of course you can stop before the top of the atmosphere, such as 60/to/137, but you have to select the maximum level number as the last one. Table 2 in the `scientific model description paper <https://www.geosci-model-dev-discuss.net/gmd-2019-358/>`_ gives an overview of the level lists and the corresponding introducstion date. |
---|
41 | |
---|
42 | |
---|
43 | .. note:: |
---|
44 | |
---|
45 | Remember that model level 1 corresponds to the top of the atmosphere and then increases in the direction of the surface. |
---|
Note: See
TracBrowser
for help on using the repository browser.